We can’t specifically address the set up for every sprinkler system,
but here are the basics on starting your
sprinkler for the season. Please wait until the nighttime
temperatures have been above freezing for a
minimum of two weeks prior to attempting to start your system.
Step One: Check your valve box drains
There is at least one valve box in your yard. They are the boxes
flush with the ground with a green lid. If we
installed your sprinkler, one will be straight out from the backflow
device on the side of your house. You might
have one for the front, one for the back and one small circular
one near the house if you have drip irrigation.
The larger your system, the more valve boxes you are likely to find.
OPEN the box lid and check for any
manual drains. If the box is full of dirt, gently move it out of
the way, avoiding any wires in the process. A dirt-
filled box is perfectly normal. Manual drains will look like a
hose bib with a flat of round rubber coated handle.
Many sprinklers installed in the last decade have auto drains.
You will also need to close any hose bibs or pool
fill valves that may be connected to your sprinkler system.
Step Two: Set your vacuum breaker/backflow device
This is the brass device with two handles on the outside of your
house. This will typically be found just above
or outside where your water meter is in your home. You will need
a small flat blade screwdriver for this step. If
your sprinkler was properly winterized last fall, the handles
should be at 45-degree angle half-way between the full on and full off position
and the screws on the small test cocks below them should have the line on the
head of the screw going with the pipe it is on, or in the open
position. We are going to use the two-step
method for setting the backflow, meaning that we are going to
fully close the backflow, turn on the water
inside and then come back and open it. If you forget the second
part, your sprinkler isn’t going to run. Turn the
two handles so they go across the pipe they are on (they sit in opposite
directions, so one will be vertical and
one horizontal). This step closes the two ball valves in the backflow.
When that is done, use your screwdriver
to turn the small screws on the test cocks 1/4 turn so that the
line on the head of the screw is across the pipe
rather than with the pipe. Turning these screws closes the test
cocks which are the drains for the backflow
device.
Step Three: Turn on the water to the backflow
Your water supply to the irrigation is typically in the basement
utility room. Locate the flat handle that is above the drain for the sprinkler
system. Make sure the drain for the sprinkler is closed (righty-tighty!) before
you turn the water on. The handle for the ball valve that controls the
sprinkler water will be going across the pipe indicating the water is off. When
you find the correct handle, slowly turn the water on to the sprinkler. You should
feel the water flowing through the pipe. Make sure you have the water fully on
before you stop turning the handle as the backflow device outside will not set
without full pressure. The water should run for about 45 seconds or so and then
stop. If the water does not stop flowing, you either have left something open
at the backflow or it has a leak. If this happens, turn the water in the
basement off and check the device.
Step Four: Open the backflow
In step two we closed off the water flow to the backflow. If all
is well and the water has stopped flowing from
turning on the water in step three, then we return to the backflow
device to open the ball valves. You will need to turn both handles, one at a time,
to the fully open position. The position of the handles will vary depending on
the positioning of your backflow device, but instead of having the handles across
the pipe or fully closed, the handle will be laying in the same direction as
the pipe it is on. Start with the ball valve that is closest to where the water
comes out of the house. When you turn the handle, the device will spit and make
some noise as water moves in it. When the backflow is full, the water will
stop. If your device is freeze-damaged, this is the step where that is found.
If water is spraying out anywhere other than a little spit out the top as it fills,
turn off the backflow and call for service. If the device holds water, then open
the other handle to allow the water to flow out to the sprinkler system. Again,
you will likely hear hissing and may get a little spitting of water out the top
of the backflow device. This is normal and will stop as the device is re-pressurized.
Step Five: Test system and set controller
Now that the water is on downstairs and at the backflow it is time
to make sure everything works well.
Manually start your sprinkler system. Check each zone for proper
operation. Walk your yard and check for
leaks. After ensuring your system is operating properly, set
your controller to run as needed. One or two days
a week is more than adequate for early season watering. Better
yet, hold off consistent supplemental watering as long as you can to give your
awakening roots a chance to develop.